Home > Dryer > How To Wire A Dryer Cord

How To Wire A Dryer Cord

Dryer+Extension+Cord+4+ProngDoes any person know exactly where I can get one? My dryer’s cord is 36 inches as well quick and cannot reach the 240V outlet. Most 3-wire cords do not have colored wires, so instead of matching colors, recognize the wires using the relative position of the wires in the cord. The center wire of the three will usually go to the center (white) terminal the outer two wires go to the outer terminals. The outer two wires can be interchanged, but never put the center wire of a flat, three-wire cord on something but the center terminal.

Data contained inside is researched and backed by experienced DIY technicians. FOR Security: Go to the dryer manufacturer’s web-site and obtain the wiring diagram on how to attach the cord correctly. The replacement cord you purchased may possibly also have a How To Wire” diagram on it also. The dryer may perhaps also say on the back what colour and where the wires connect. Petra 4′ 3 wire 240 volt ( rated to 250 volt) dryer cord / connector. 3- # 10 gauge SRDT – 30 amps – 250 volts – 7,500 watts. 1.23 meters in length.

Get rid of every single wire from the screw or stud holding it, producing sure to save all nuts or screws. There will be some kind of connector holding the dryer cable to the wall of the dryer so that it does not pull out. The most widespread kind is a clamp with two screws on the outdoors that can be tightened to squeeze the wire into place. Loosen these screws so that the wire can slide out of the dryer.Dryer+Extension+Cord+4+Prong

Begin by unplugging the dryer. There is higher voltage inside (240 volts) that can give you a extremely nasty shock, even kill you. Make certain there is no chance of this, by unplugging the dryer prior to proceeding any additional. Get behind the dryer and take away the terminal block access panel (smaller panel with generally one particular screw securing it). Take away the cover plate from the wire terminal block, exposing the wires inside. Note where every single color of wire terminates. Generally, you will see a row of three terminal screws, with the red and black wires connected to the two outdoors screws, the white wire connected to the center screw, and the green wire connected to the frame of the dryer.

Most 3-wire cords do not have colored wires, so alternatively of matching colors, recognize the wires employing the relative position of the wires in the cord. The center wire of the 3 will always go to the center (white) terminal the outer two wires go to the outer terminals. The outer two wires can be interchanged, but never ever place the center wire of a flat, three-wire cord on something but the center terminal.

After the 4-wire cord is removed, it is time to install the new 3-wire cord and plug. Operate the wire by means of the connector, but do not tighten it but. The red and black wires go to the outer two terminals (in the photo the dryer wires are black and blue) and the white wire goes to the terminal in the center of the terminal block. Whilst the red and black wires are interchangeable, the white wire is not make confident it goes to the center terminal, exactly where the old white wire was.

Get rid of every single wire from the screw or stud holding it, generating sure to save all nuts or screws. There will be some sort of connector holding the dryer cable to the wall of the dryer so that it does not pull out. The most typical form is a clamp with two screws on the outside that can be tightened to squeeze the wire into location. Loosen these screws so that the wire can slide out of the dryer.

Start by unplugging the dryer. There is high voltage inside (240 volts) that can give you a incredibly nasty shock, even kill you. Make sure there is no opportunity of this, by unplugging the dryer prior to proceeding any additional. Get behind the dryer and take away the terminal block access panel (tiny panel with typically one particular screw securing it). Get rid of the cover plate from the wire terminal block, exposing the wires inside. Note exactly where every colour of wire terminates. Ordinarily, you will see a row of 3 terminal screws, with the red and black wires connected to the two outdoors screws, the white wire connected to the center screw, and the green wire connected to the frame of the dryer.

The photo shows a metal strap installed it goes from the white wire down the side of the terminal block, and is screwed to the dryer frame. If this strap is not out there (and it usually is not) purchase a one particular-foot piece of #10 green wire, strip an inch of insulation from each and every end, and install that wire involving the connector the white wire employed to go to and the connector on the frame exactly where the green wire employed to go.

When the 4-wire cord is removed, it is time to install the new three-wire cord and plug. Operate the wire by way of the connector, but do not tighten it but. The red and black wires go to the outer two terminals (in the photo the dryer wires are black and blue) and the white wire goes to the terminal in the center of the terminal block. Whilst the red and black wires are interchangeable, the white wire is not make positive it goes to the center terminal, where the old white wire was.

Leave a Reply