Depends a lot on how far the dryer is from the wall, what material the wall is produced of, and which way your floor joists run. Okay, so I was now facing glitch number one. After looking at the instructions additional very carefully, (shame on me) I realized that when installing the retrofit box for current building the dryer box is supposed to sit flush with the drywall… OMG. I was supposed to trace the box, then measure inside the line, mark a new line, and THEN reduce. OMG. I was so mad at myself. Careless error. I tried not to scream be concerned as well considerably and just believed, Effectively I can patch a small bit of drywall following I get this pipe installed”.
This was not working. This was glitch quantity two, three, 4, and 5. I was truly trying not to hate my new dryerbox. Immediately after a great deal wrestling and even involving my foot to hold this box up against the wall, even though I tried to force this pipe via the narrow, unrealistic opening, I was left with a crunched up, tiny piece of pipe that I could never straighten out again…sigh… I study step 7 for some hope.
After my miraculous installation, I went on to patch the drywall, caulk, and paint. Immediately after I completed patching I decided to use some painters tape to stay clear of obtaining any more mess on the edge of the dryerbox. Taping ahead of caulking is much less difficult than cleaning the edge of the dryerbox. Soon after applying caulk and smoothing it out, I peeled the tape off just before it dried, which gave me a perfect caulk line. When the caulk was dry, I taped my edges for the final time, and painted.
The very first rule when connecting the dryer to the semi-rigid vent hose is don’t use foil tape in this place. The dryer demands to be easily moved so that the duct can be cleaned out periodically and trying to replace foil tape each time just is not practical. For this connection I used a clamp that can be tightened with a screwdriver. This tends to make disconnecting the dryer a great deal less difficult. This end was already prepped and flattened from when I rolled it with my PVC pipe earlier, so all I had to do was slip the connector on, hook it up, and tighten the screw.
Seriously? This says it is supposed to assistance you get the pipe into the oval (not round like the vent pipe) opening in the best of the dryer box. Feeling skeptical, and soon after reading the directions extremely very carefully (specially following my earlier mishap) I decided to go for it. I grabbed my pliers, and as instructed, twisted the bottom of the pipe into what looked like a contorted mess.
I knowledgeable equivalent frustrations with my install. I cut the oval hole out huge sufficient to get the pipe through. In the end it looks fantastic and works very good but was not an quick set up. I am so excited to have discovered this on Pinterest. My dryer existing sticks out farther than yours did and is continually finding banged by the door. I am absolutely not brave enough to do this on my own so I’ve sent your weblog web page to my dad, Mr. Handy Man. He loves to pay a visit to me (reside in various states) once or twice a year and do handy projects for me.
Okay, so I was now facing glitch number one. Immediately after seeking at the directions more very carefully, (shame on me) I realized that when installing the retrofit box for current construction the dryer box is supposed to sit flush with the drywall… OMG. I was supposed to trace the box, then measure inside the line, mark a new line, and THEN cut. OMG. I was so mad at myself. Careless error. I attempted not to scream worry as well much and just thought, Properly I can patch a small bit of drywall just after I get this pipe installed”.
This was not functioning. This was glitch number 2, 3, four, and five. I was really attempting not to hate my new dryerbox. Just after a lot wrestling and even involving my foot to hold this box up against the wall, while I tried to force this pipe by way of the narrow, unrealistic opening, I was left with a crunched up, tiny piece of pipe that I could never ever straighten out again…sigh… I study step 7 for some hope.
For the most important or higher floor in a typical wood frame house with the dryer inside about 10 feet or so from where the outdoors vent will be, if the duct can run from the back of the dryer straight down into the floor, then soon after a 90 degree turn run between the floor joists to the outside wall without the need of hitting any other ductwork or plumbing that it cannot get around, might be as small as $150-300 based on irrespective of whether the floor joists are exposed or not.